Description
New 7,500 RPM Grease Pack (GP) spindle for your Fadal Machine.
These spindles are built with precision matched bearing pairs over-rated to 12,000 RPM & based on current Japanese machine tool spindle designs.
This equates to a 100% duty cycle on your machine tool...and that means more money for you at the end of the day.
All spindles setup and fully ran-in before shipping. This includes:
1) Balanced to 10,000 rpm
2) Use precision NSK bearings
3) A newly designed labyrinth seal to stop contamination from entering the spindle nose
4) Are vibration tested after assembly to insure the bearings are seated properly and run-in
These spindles have successfully withstood the test of time with over 1,000 installations in the US and other countries around the world.
The spindle comes with a new draw bar replacement kit. Please specify a Locking Drawbar (10k High Torque) or Non Locking Drawbar.
We stand behind our spindle with a 2 Year Limited Warranty! See OTHER DETAILs Tab.
Contact us directly if you have and questions about your spindle or the new spindle.
We Include Step by Step Spindle Remove and Replace Instructions!
We include the absolute best instructions!
Most copy the Fadal Maintenance Manual and expect you to figure it out!
Our instructions are designed so a person with basic mechanical experience can remove and replace a Fadal Spindle.
Why we Don't sell "Rebuilt" Spindles
While buying a "rebuilt" spindle might seem like a good idea, the problem is you don't know the history why the spindle failed!
The fact is that Fadal actually had over a dozen different design over the years.
The engineering changes were made to improve the spindle life and performance.
- Spindle Preload design changed
- Overtime the number of tool retention springs varied from 19 belleville springs to eventually 44 springs. The lower the count, the shorter the tool in/out duty cycle!
- The list goes on...
Typically, the rebuild is not an actual or complete rebuild that would bring the old design up to the latest. Why? That's because the cost would be to expensive.
The usual "rebuild" consists of simply cleaning, a bit of polishing and replacing the bearings.
The bottom line is you do not know the actual version the "Rebuilt" and how or if it was really "Rebuilt".
Information about Spindle Failure
Spindle Failure - Bearing failure is the most common reason for a spindle to fail. Today it seems the "end all" solution is to sell you an "upgrade" to Ceramic Bearings. Ceramic bearings are not new, they've been around for over 30 years. While ceramic bearing are in some cases "better", as the saying goes "Better is the enemy of Good". First off, not all ceramic bearings are the same, secondly if ceramic bearings were so good, they'd be the standard of the industry. There are many different ceramic bearings; the best are solid ceramic while the cheapest are steel bearings coated with ceramic.
The basic advantage of a ceramic bearing is roundness, stiffness and weight, which depending on the application can make the difference between success and failure, especially above 20,000 rpm.
Stiffness can cause chatter which is a factor of bearing stiffness, span, preload and shaft design. It's all a balance of design, the ultimate design is to have more bearing preload at the lower rpm and less preload and the higher rpm range. In the early development of the Fadal spindle we actually had experimented with a dynamic preload spindle. It automatically changed the preload according to the rpm. Unfortunately it was too complicated for production.
The correct preload is a balance between spindle rpm ranges- higher rpms require less preload between the bearings. Less preload reduces the heat but increase spindle "chatter" during low rpm cutting.
The biggest cause of spindle failure is Contamination and/or Heat.
Below is a list of common reasons why spindles fail.
Contamination: Typically, coolant gets by the labyrinth seal at the spindle noise and brakes down the spindle grease. It's easily detected as the grease turns a milky white color.
Heat: Another spindle killer. Duty cycle and preload contribute to spindle heat failure. A simple way to tell when a spindle is running hot is by checking half way up the spindle taper. At this point the inner race of the bearings is at the thinnest point of the spindle shaft wall thickness. The rule is "if you can't keep your finger on it at this point; it's too hot". A simple warm-up procedure; 5000 rpm for 10 minutes in the morning is very important for all grease pack spindles. It helps to distribute the grease evenly, after sitting over night. Increase the warm-up time as the off time increases.
Belt Tension: The HI/LOW idlers need to be cycled. Shifting ranges relieves the belt tension caused by the hydraulic idlers. The torque of the belt causes the idler to keep going inward which increases the belt tension between the spindle motor and the spindle pulley. This causes an excessive load on the top spindle bearings which increases the heat factor. This heat factor can cause the grease to migrate down away from the top bearings. Also, cycling the idlers will increase the belt life by reducing tension on the belts.
Air Pressure: Another important check is to verify the idler air supply is less than 70 psi. The machine has two regulators; one for the tool in/out and one for everything else. Too much pressure to the idlers will cause excessive belt tension and damage the top bearings.
Spindle Coolant: Verify that the coolant flow hasn't been reversed. The coolant must flow into the bottom of the spindle and out the top of the casting (return line). It's easy to get the lines backwards.
Cooling: Verify the chiller system is full and cycling correctly. The temperature differential of the chiller input verses its output is about 1.5 degrees. The BTU capacity of the chiller must not be exceeded by the run time of the spindle; the chiller system needs spindle off time to reduce the heat inside the spindle. For excessive duty cycle, considers adding another chiller.
Tool Crash: Crashing the tool into the part can cause bearing ball/race damage and/or actually bend the spindle shaft enough to cause bearing failure.
History: Fadal came out with the first machine with 10,000 rpm for under $50k. Many thought it was impossible since the average machine had a top speed of 6,000 rpm. At the time 10K rpm and above was very expensive and doing it with a 40 taper was unheard of. Spindle manufactures at the time would quote "a buck an rpm" and the warranty was rated in hours, not years. At Fadal, the idea was higher rpm, faster feeds, more money.
